carfobbattery

Ford Bronco key fob battery

6 of the 7 model years listed for the Ford Bronco have a proven battery. The most common answer is CR2450. Rows below run oldest to newest; a year can appear twice when the car came with more than one kind of key.

  1. 1996Remote (separate)

    2 x CR2016

    FCC ID GQ43VT4T

    Two sites agree: keylessentryremotefob.com and carandtruckremotes.com (checked Nov 1, 2026)

    Find CR2016 on Amazon
  2. 2021Flip key

    CR2032

    FCC ID N5F-A08TAA

    Two sites agree: americankeysupply.com and uhs-hardware.com (checked Nov 1, 2026)

    Find CR2032 on Amazon
  3. 2021-2022Smart key

    CR2450

    FCC ID M3N-A2C931426 / M3N-A3C108397

    Two sites agree: americankeysupply.com and energizer.com (checked Nov 1, 2026)

    Find CR2450 on Amazon
  4. 2023Smart key

    CR2450

    FCC ID M3N-A2C93142300

    Two sites agree: bestkeysupply.com and energizer.com (checked Nov 2, 2026)

    Find CR2450 on Amazon
  5. 2024Smart key

    Not confirmed yet

  6. 2025-2026Smart key

    CR2450

    FCC ID M3N-A3C108397

    Two sites agree: uhs-hardware.com and bestkeysupply.com (checked Nov 2, 2026)

    Find CR2450 on Amazon

Changing the battery

Separate remote fob

  1. The remote is a small standalone unit. You will not need to touch the ignition key at all.
  2. Turn it over: some older fobs use one small screw, newer ones just clip. Pry at the seam once any screw is out.
  3. Lift the old coin cell out and press the new one in with matching orientation.
  4. Close the fob and test it. If it does not work, open it again and check the cell is seated flat.

This key takes two CR2016 cells. Change both at the same time and stack them the way the old pair sat; mixing a fresh cell with a tired one shortens the life of the new one.

Flip key

  1. Fold the blade out so it is out of the way, or keep it folded if your case opens from the side; the battery sits in the plastic body, not the blade.
  2. Find the seam or small slot on the body (often at the end away from the blade) and twist a coin or small flat screwdriver in it until the cover lifts.
  3. Lift the cell out with a plastic tool and press in the new one with the + side matching.
  4. Press the halves together until no gap shows, then try every button.

A CR2032 is 20 mm across and 3.2 mm thick. CR2032, CR2025 and CR2016 share the same width but not the same thickness, so a swap between them can leave a loose contact or a case that will not close.

Smart key (push-button start)

  1. Find the small release on the edge or back of the fob and hold it while you pull out the metal emergency key.
  2. Use the slot where the metal key sat. Twist, do not lever hard, and work along the seam until the halves separate.
  3. Note which side of the old coin cell faces up (usually the side with the writing), lift it out with a plastic tool, and press the new one in the same way.
  4. Close the case until it clicks all the way round, put the metal key back, then try the buttons and a push-button start.

Ford intelligent access fobs usually have a release for the emergency key. The key blade itself fits the pry slot.

A CR2450 is 24.5 mm across and 5.0 mm thick, much fatter than a CR2032. A thinner cell will rattle and lose contact, so buy the exact size.

Coin cells are a choking and burn hazard for children. Store the spares in their original pack, out of reach.

Other Ford models